Vehicles
295 not categorized PORSCHE 356 B HEATERCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.96421132303 Known as: hot air socket View/Change Diagram
From $173.00
Make a selection 96457201501 As with any fan, bearings can fail, they can draw a high number of amps or there can be an electrical failure. Replace as needed and odds are that if the left side has failed the opposing side may be on the way out also, the right side is part # 96457201601 sold individually. 1 necessary per car. View/Change Diagram
From $136.33
Make a selection 96562415100 If your windows steam up easily or the temperature inside the cabin doesn't raise quickly enough, most likely the blower motor in the engine compartment is defective or worn out. This cost-effective blower motor is a direct replacement manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For 965 models, we recommend replacing the resistors, part # 96561610100 and resistor housing, part # 93021124001 to save on lab...(choose a part on the right to read more) View/Change Diagram
From $317.50
Make a selection 98661315200A02 Known as: gloss black seat heater View/Change Diagram
$51.63
Make a selection 94810605906 Known as: cooling water tube heating View/Change Diagram
From $128.42
Make a selection 99610642474 Known as: hose return line View/Change Diagram
$108.70
Make a selection
$39.62
Make a selection 99661315410A05 View/Change Diagram
$57.20
Make a selection M092 Rennline's blower motor bypass pipe is a carbon fiber replica of the factory installed unit found on the lightweight 3.6 rs race cars. This pipe allows you to save 9 pounds from the removal of the factory blower motor assembly, but still have a functioning heater system in your car. Manufactured from ultra strong, lightweight carbon fiber and comes equipped with the aluminum fitting for the distributor breather tube. Custom insignias are available upon request (insignia size limited) call for details. Fits 964 89-98 except 95's 993's require the 964 fan shroud part # g96410640302. General Fitment911 1989-94911 1994-98
$265.00
Make a selection 99610643474 Known as: hose supply View/Change Diagram
$39.56
Make a selection 99757255300 Known as: heater hose zulauf / heater hose intake View/Change Diagram
From $26.00
Make a selection FSPOR964CFHB Product details: General Fitment911 1989-94
$350.00
Make a selection FSPOR993CFHB Product details: General Fitment911 1994-98
$350.00
Make a selection 993624328012 The heater blower blows hot air from the exhaust heat exchangers into the interior via the vents. The blower housing is located atop the engine. This unit is a replacement motor and fan for the heater blower, does not include housing. Sold individually. 1 necessary per car.
$317.90
Make a selection I206 Radio and heater control block off plates - until now, removing the center console from your 964/993 was not possible due to the required switches that were mounted in it. Rennline's new radio and heater control block off plates solve that problem. These plates have been specially designed to accept the factory switches installed in the center console of all 964/993 cars. Don't have the factory switches? No problem. These plates are also available without switch cutouts so you can install your own switches or gauges. Made from powder coated metal and installs in minutes on cars with the radio or heater controls removed. General Fitment911 1989-94911 1994-98
$50.00
Make a selection I203 Radio and heater control block off plates - until now, removing the center console from your 964/993 was not possible due to the required switches that were mounted in it. Rennline's new radio and heater control block off plates solve that problem. These plates have been specially designed to accept the factory switches installed in the center console of all 964/993 cars. Don't have the factory switches? No problem. These plates are also available without switch cutouts so you can install your own switches or gauges. Made from powder coated metal and installs in minutes on cars with the radio or heater controls removed. General Fitment911 1989-94911 1994-98
$50.00
Make a selection M091 Rennline's blower motor bypass pipe is a carbon fiber replica of the factory installed unit found on the lightweight 3.6 rs race cars. This pipe allows you to save 9 pounds from the removal of the factory blower motor assembly, but still have a functioning heater system in your car. Manufactured from ultra strong, lightweight carbon fiber and comes equipped with the aluminum fitting for the distributor breather tube. Custom insignias are available upon request (insignia size limited) call for details. Fits 964 89-98 except 95's 993's require the 964 fan shroud part # g96410640302. General Fitment911 1989-94911 1994-98
$299.00
Make a selection M0507B Removing the blower motor assembly from your 1989-98 964/993 is a very standard modification for cars that want to loose a few pounds. This modification reduces your cars weight by about 10 pounds and really cleans up the engine bay. This kit is an exact replica as used by Porsche motorsports for the factory lightweight 964 cup and 964 rsr race cars. Manufactured from aluminum and is available in red and black powder coat or clear anodized. Comes with all the stainless steel hardware required for a 20 minute installation. Will not work on turbo cars. Black in color. General Fitment911 1989-94911 1994-98
$115.50
Make a selection M093 Rennline's blower motor bypass pipe is a carbon fiber replica of the factory installed unit found on the lightweight 3.6 rs race cars. This pipe allows you to save 9 pounds from the removal of the factory blower motor assembly, but still have a functioning heater system in your car. Manufactured from ultra strong, lightweight carbon fiber and comes equipped with the aluminum fitting for the distributor breather tube. Custom insignias are available upon request (insignia size limited) call for details. Fits 964 89-98 except 95's 993's require the 964 fan shroud part # g96410640302. Note: 3.8 insignia shown. General Fitment911 1989-94911 1994-98
$265.00
Make a selection FVD21168300 Cost effectively repair your heater box flap with this kit. We source these parts from Porsche ag in Germany to ensure quality, reliability and precise fitment.
$11.95
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |